designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print no of positions length * (in millimeters) -0500 - 9999 *contact samtec for custom lengths. -1000, 2000, 3000, and 5000 in stock lengths longer than 5000 not supported by test data -19: (5 sig pairs/4 power lines) uses hdmip-19 (see fig. 1) -29: (8 sig pairs/6 power lines) uses hdmip-29 (see fig. 2) hpstp-xx-xxxx-xx-xx second end -s: standard plug available second end: (19 and 29 position) -standard plug -m: mini plug available second end: (19 position only) -m: mini plug -s: standard plug -sl: locking standard plug available second end: (19 position only) -sl: locking second plug -ml: latching mini plug available second end (19 position only) -ml: latching mini plug -s: standard plug available first end: (19 and 29 position) -s: standard plug -m: mini plug -m: mini plug available first end: (19 position only) -m: mini plug -sl: locking standard plug available first end: (19 position only) -sl: locking second plug -ml: latching mini plug available first end (19 position only) -ml: latching mini plug first end (see callout) length 1% 4.45 ref. .175 (see table 1) "c" ref. "f" ref (typ) stpc-xx-02-xxxx c1 (see table 1) "a" (see table 1) "d" ref "e" ref (typ) c2 fig. 1 hpstp-19-xxxx-s-s shown hdrl-11 (see note 11) label-et (see note 3) 1 2 18 19 1 2 c c4 c3 c5 sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: .3 [.01] 2 .xx: .13 [.005] .xxx: .051 [.002] material: hdmi shielded twisted pair cable assy by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 2/23/2006 7 1 sheet scale: 1:1 f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. all assemblies to be 100% electrically tested. 3. all assemblies to be 100% hi-pot tested at 300v. after final electrical test, label each assembly with 1 label-et. 4. wrap ends in bubble wrap and package in clear poly bags. 5. see table 2, 3, 4, & 5 for signal/ground/power configuration. 6. connector sheild tied to braided cable shield. 7. gold shall be .000030" min gold per mil-g-45204b, class 1, to be measured in contact area. 8. nickel shall be .000080" min per qq-n-290, class 1, measured on shell. 9. note deleted. 10. note deleted. 11. hdrl-11 is to be centered on cable as shown. hdrl-11 is to contain: part number, shop order, & date code. overmold: pvc (ul94 v-0) premold: pe (ul94 v-0) connector: lcp (ul94 v-0) cable: (vw-1) 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision u
fig. 2 hpstp-29-xxxx-s-s shown 29 28 2 1 fig. 3 hpstp-19-xxxx-sl-sl shown 02 01 19 18 10.42 ref .410 30.84 1.214 ref (typ) 6.50 .256 (see part callout) length 1% 14.00 max .551 5.25 .207 overmold sub-mhdmc-19-x 2.42 ref .095 8.40 max .331 'c' j1 j2 'a' detail 'c' (latching option only) 01 19 detail 'a' 0.45 ref .018 2.62 ref .103 5.25 .207 20.3[.799] .045 ref 10.9[.429] .045 ref 'b' (hpstp-19-xxxx-ml-ml shown) detail 'b ' (non-latching) (hpstp-19-xxxx-m-m shown) detail 'b ' (latching) j2 19 18 01 02 fig. 4 hpstp-19-xxxx-ml-ml shown (shielded twisted pair only) fig. 5 hpstp-19-xxxx-m-s shown (same as fig. 1 and fig. 4, different as shown) (shielded twisted pair only) sheet of hdmi shielded twisted pair cable assy by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 2/23/2006 7 2 sheet scale: 1:1 f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw revision u 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
sheet of hdmi shielded twisted pair cable assy by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 2/23/2006 7 3 sheet scale: 1:1 revision u f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
assembly length 1% (see table 1) "a" sub-hdmip-xx-01 copper foil stpc-xx-02-xxxx copper foil sub-hdmip-xx-01 fig 1. hpstp-19-xxxx-01 shown (-s-s option only) c2 c1 "l" (ref) 2:1 scale for clarity 1 18 19 1 2 2:1 scale for clarity sheet of hdmi shielded twisted pair cable assy by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 2/23/2006 7 4 sheet scale: 1:1 revision u f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
assembly length 1% assembly length - 36.5mm[1.44in] 1% cable length = 'd' stpc-xx-02-xxxx sub-hdmip-xx-01 sub-hdmip-xx-01 solder terminate cable to pc boards pin 1 pin 1 in-process - step 1 (hpstp-19-xxxx-s-s shown) a) slide 6mm heat shrink tube over pairs and conductors b) solder cable to pcb c) push h/s tube up to pcb and activate (see detail) first end second end heat shrink tube (typ) (after shrinking) 1.40 .055 19.05 .750 19.00 .748 3.60 .142 jacket braid shield twisted pair shield dielectric inner conductor strip dims in-process - step 2 (hpstp-19-xxxx-s-s shown) a) apply epoxy b) trim braid to 4mm wide tails on this side only (do not trim length) keep epoxy within pad area epoxy region 01 02 18 19 01 02 18 19 6.00 .236 detail 'd' scale 2 : 1 heat shrink detail heat shrink tube (use hst-0.078-02-blk) 4.00 .157 hdmi shielded twisted pair cable assy sheet of by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 11/7/07 7 5 sheet scale: 1:2 f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw revision u 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
copper foil solder foil to connector shield in-process - step 4 (hpstp-19-xxxx-s-s shown) a) add copper foil (cut 1.0) over premold b) trim braid to 6mm c) solder braid to copper foil and solder copper foil to connector solder braid to foil "j" (typ) "k" - .20 (typ) (see table 2) "g" - .20 "h" (typ) premold premold 2:1 scale for clarity 2:1 scale for clarity in-process - step 3 (hpstp-19-xxxx-s-s shown) a) add premold b) clip alignment tabs flush with premold (+.010/-.000) "l" - .20 "m" (typ) stpc-xx-02-xxxx sub-hdmip-xx-01 sub-hdmip-xx-01 clip alignment tabs (8x) hdmi shielded twisted pair cable assy sheet of by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 2/23/2006 7 6 sheet scale: 1:2 f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw revision u 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
(see table 1, sht 1) "a" (see table 1, sht 1) "d" ref (see table 1, sht 1) "e" ref (typ) c2 in-process step 5 (hpstp-19-xxxx-s-s shown) add overmold (pvc) and labels hdrl-11 (see note 11) label-et (see note 3) 01 02 18 19 01 02 18 19 01 02 ground (1) white (2) green (2) ground (3) white (4) blue (4) purple (p) orange (5) pink (p) hpstp-19-xxxx-s-s shown white (1) brown (1) ground (2) white (3) red (3) ground (4) white (p) yellow (5) ground red (p) hpstp-29-xxxx-s-s shown 01 02 white (1) yellow (1) ground (2) white (3) orange (3) ground (4) ground (6) white (5) red (5) white (7) brown (7) brown (p) orange (8) red (p) white (p) ground (1) white (2) green (2) ground (3) white (4) black (4) ground (5) white (6) blue (6) ground (7) black (p) purple (p) yellow (8) gray (p) (p) = power (x) = pair number (p) = power (x) = pair number custom hdr cable assembly sheet of by: hpstp-xx-xxxx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing john riley 2/23/2006 7 7 sheet scale: 1:2 f:\dwg\misc\mktg\hpstp-xx-xxxx-xx-xx-mkt.slddrw revision u 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
